Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Dryer Vent Cleaning Across Long Beach
Dryer vent cleaning in Long Beach typically runs $135 – $265 for a single-family home, and most jobs take 60 – 90 minutes from setup to final airflow test. We work the entire Long Beach grid, from the Craftsman bungalows of Rose Park to the mid-century tracts in Los Altos, and we know what coastal air does to a vent system. If you’ve put off the service or you’ve just moved into an older Long Beach house, call (855) 382-6159 and we’ll get you a free estimate with camera inspection included.
This is fire-prevention work, not a convenience call. A clogged dryer vent is a fire waiting to happen, per NFPA standards, and Long Beach’s combination of ocean humidity, salt corrosion, and palm debris puts older hoods and flues at higher risk than inland cities. We treat Dryer Vent Cleaning as front-line venting safety, done by the same technicians trained in combustion venting who handle our chimney work.
Why Corona Chimney Sweep Is Long Beach’s Preferred Dryer Vent Cleaning Company
Long Beach homeowners call us because we repair what we find. A lot of dryer vent companies clean the lint and leave. We inspect the entire vent path with a camera, and when we find a crushed transition duct behind a 1950s wall in Lakewood Village or a vent routed into a chimney flue in Belmont Shore, we fix the problem on the spot rather than handing you a referral and wishing you luck.
Nolan Ferris built Corona Chimney Sweep to do three things under one roof: chimney sweeping, chimney repair, and dryer vent cleaning. That scope matters in Long Beach, where many dryers vent through or near chimney structures that haven’t been touched since the home was wired for a gas dryer. Our Long Beach customers get a single provider for every venting hazard involving their house.
We stock materials from six contractor-grade brands: DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. These are the product lines professional contractors source from supply houses, not big-box substitutes. When a Long Beach vent needs a new cap or a rusted section replaced, we’re not putting on whatever the local hardware store had on the shelf.
Styles & brands we work with
Our Dryer Vent Cleaning Services in Long Beach
Dryer Vent Cleaning
We remove built-up lint from the dryer’s internal lint trap housing, the transition duct behind the appliance, and the full exhaust run to the exterior termination point. In Long Beach’s older homes, that run is often longer than code allows, with unnecessary bends that collect lint faster. After cleaning, we test airflow at the exterior hood and show you the before-and-after camera footage. Flat price agreed before we book the appointment, no surprise add-ons.
Chimney Inspection
When a dryer vent shares a wall or chase with a chimney, or when a dryer was historically vented into a chimney flue, a camera inspection of both paths is non-negotiable. Long Beach’s 1920s – 1950s bungalows in 90803 and 90804 frequently have dryer exhaust terminating into unlined brick or clay-tile flues that were never engineered for that purpose. We document the vent path, identify blockages from palm fronds or bird nests, and recommend only what the camera evidence supports.
Chimney Cap Installation
A missing or crushed chimney cap is the single biggest source of debris in Long Beach dryer vents that route near chimney structures. Palms drop fronds, pigeons move in, and salt air corrodes the cap’s fasteners until it walks off in a Santa Ana wind. We install stainless steel caps from Gelco and Olympia Chimney, sized to the actual flue dimensions rather than whatever “universal” clamp was on sale. For homes in 90802 and 90803, this is often the difference between cleaning the vent once and cleaning it twice a year.
Dryer Vent Rerouting
Some Long Beach dryers need their exhaust path rebuilt entirely. When the vent runs into a chimney flue, snakes through a crawl space for thirty feet, or terminates under a deck where hot lint accumulates against wood framing, the right fix is rerouting, not repeated cleanings. We handle the full modification, from cutting the new termination point to sealing the abandoned one. You get one invoice and one responsible party for the whole job.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Long Beach
We install and service dryer vent components and chimney materials from DuraFlex, HeatShield, Gelco, and Olympia Chimney. DuraFlex flexible liner systems matter here because Long Beach’s older homes often have masonry or clay-tile flues that are not compatible with rigid duct. HeatShield resurfacing lets us restore a deteriorated flue interior without a full liner replacement where conditions qualify, an option sweep-only companies in Long Beach simply cannot offer. We keep parts in our trucks and in local stock for the ZIP codes we cover: 90801, 90802, 90803, and 90804.
Common Dryer Vent Cleaning Problems We See in Long Beach Homes
- Palm fronds and bird nests packed into dryer vents. In the bungalow blocks of 90803 and 90804, missing or crushed chimney caps let fronds drop straight into the flue. When a dryer vents into that same stack, the result is a blocked vent that no amount of lint brushing will solve. We remove the debris and install a proper cap.
- Salt-air corrosion on vent hoods and terminations. Long Beach’s marine air eats galvanized and cheap stainless hoods within a few years. Flaps seize shut, which forces hot, lint-laden air back into the laundry room. We replace corroded terminations with marine-grade stainless.
- Dryer vents routed into unlined chimney flues. Common in 1920s – 1950s Spanish Revivals and California bungalows. The flue was built for wood smoke, not warm lint. Heat and moisture from the dryer accelerate spalling inside the flue, and lint plus spalled brick equals a real fire risk. Camera inspection shows it; we reroute but only when rerouting is actually required.
- Long, sagging flex duct in crawl spaces. Many mid-century Long Beach homes in 90805 and 90808 have dryer duct runs that dip and sag under the floor. Moisture condenses in the low spots, lint sticks, and the pipe clogs. We replace sagging sections with rigid duct where code and access allow.
See the difference
Before
After
Before
After
Before
AfterPricing for Dryer Vent Cleaning in Long Beach, CA
A standard dryer vent cleaning for a single-family home in Long Beach runs $135 – $265. That covers removing the dryer to access the transition duct, cleaning the full vent run with rotating brushes, and an airflow test at the exterior hood. Homes where the vent shares a chimney chase or terminates on a second-story roof run higher, typically $195 – $310, because of ladder work and longer pipe runs.
Chimney cap installation runs $145 – $385 in Long Beach depending on flue size and whether we need stainless or galvanized. Camera inspection is included with every vent cleaning call at no additional charge; you see the blockage before we quote any repair. Never a recommendation for liner work or masonry repair without camera footage you can watch yourself. For an exact quote in your part of Long Beach, call (855) 382-6159. Estimates are free.
We Also Serve Cities Near Long Beach
Our team covers the full Long Beach metro and surrounding communities. If you’re in Signal Hill, Lakewood, Carson, or West Carson, we bring the same camera-first inspection process and same contractor-grade materials to your vent system. Same pricing structure, same technician training, and no extra charge for the slightly longer drive.
Serving Long Beach, CA — Our Local Coverage Area
We’re based in the Long Beach area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs – Dryer Vent Cleaning in Long Beach
A chimney inspection is required when the camera shows your dryer vent is connected to, routed through, or terminating near a chimney flue. In Long Beach’s older housing stock, especially 1920s – 1950s bungalows in 90803 and 90804, dryers were frequently vented into masonry chimneys that were never meant to carry lint. The chimney inspection tells us whether the flue is blocked with palm debris, bird nests, or spalled brick, and whether the vent path can be salvaged or needs rerouting. If the camera shows a clean, separate duct run, no chimney inspection is needed. Call (855) 382-6159 for a camera-first assessment.
Salt air corrodes the metal parts of the dryer vent system faster than inland cities. Exterior hoods rust, the flap seizes shut, and in homes two to five miles from the ocean, the corrosion reaches chimney caps and chase covers that sit above the roofline. We see flue caps eaten to lace in Belmont Shore and Alamitos Heights. That corrosion lets in rain, palms, and birds, which turns a routine lint cleaning into a structural repair. Long Beach dryer vent service includes inspecting every metal component, not just brushing the pipe.
Yes, and it happens routinely. The older bungalow blocks of 90803 and 90804 are loaded with palm trees that drop fronds directly onto rooflines. A missing or crushed chimney cap gives those fronds a straight path into the flue, and pigeons will nest in any open flue within a season. If your dryer vents into or near that chimney, the lint sticks to the nest material and blockages form fast. We remove the debris, clean the vent, and install a stainless cap so it doesn’t happen again.
Expect a longer job and more findings than a newer home. The vent run is often clay tile or brick, not smooth metal duct, and it may not run directly to the exterior. We start with a camera inspection of the full path, document what we find, and show you the footage before recommending anything. On a 1920s Spanish Revival in Belmont Shore, we found the dryer venting into a chimney flue packed with palm fronds and bird nests. We removed the material, re-crowned the chimney, and rerouted the dryer to a code-compliant exterior termination. That’s the standard, not a one-off.
Annual cleaning is the NFPA recommendation for most households, and that holds in Long Beach. But if you have an uncapped chimney, a dryer vent that terminates on the roof, or palm trees hanging over your roofline, every six months is the safer schedule. Homes in 90802 and 90803 get more salt exposure and more pest pressure than inland ZIP codes, so the vent path needs checking more often. We’ll set a reminder schedule after our first visit based on what the camera actually shows in your vent.
Written by Nolan Ferris, Owner at Corona Chimney Sweep, serving Long Beach and surrounding cities.
Contact Corona Chimney Sweep
Need dryer vent cleaning, a chimney inspection, or repairs in Long Beach? Call (855) 382-6159 for a free estimate. We work across 90801, 90802, 90803, and 90804, from Belmont Shore to Los Altos to North Long Beach. One provider, every venting hazard.